Citizen BD2-2880 Uživatelský manuál

CONTROL BOARD FOR MLT-288/MLT-289MODEL BD2-2880/2890Rev. 1.00 Newly Issued Aug 9th, 2002User’s Manual

BD2-2880/2890 User’s Manual6 CAUTION:1. For LED of ERROR and PE, there is a resister of 330Ω on the circuit side to make current value 10 mA. Pl

BD2-2880/2890 User’s Manual74. DIP SWITCH SETTING(1) DIP SWITCH(2) JUMPER(3) INTERFACE & BAUD RATEDS1-11-21-31-41-51-61-71-8Auto CutterCR Selectio

BD2-2880/2890 User’s Manual8 Note:1. Input Buffer is 2k byte. (Fixed)2. Serial data length is 8 bits. (Fixed)If print tone is set at 2 or above, p

BD2-2880/2890 User’s Manual95. POWER SUPPLY5.1 SpecificationsVCC : 5V ±5% Approx. 130 mAVP : 4.2V ~ 8.5V Approx. 1.5A (Peak : Approx. 4A)

BD2-2880/2890 User’s Manual106. PARALLEL INTERFACE6.1 SpecificationsData input method : 8 bit parallel signal (DATA0~7)Control signals : ACK, BUSY, ST

BD2-2880/2890 User’s Manual11[Printer side][Host side][Printer side][Host side]All the output signals are pulled up by 50K (3) I/O Conditions ST

BD2-2880/2890 User’s Manual126.5 Data Receiving ControlWhen BUSY signal is “LOW”, data from the host can be received. When it being “HIGH”, datacanno

BD2-2880/2890 User’s Manual137. SERIAL INTERFACE7.1 Specifications(1) Data transfer system: Asynchronous(2) Baud rates1200, 2400, 4800, 9600, 19200 b

BD2-2880/2890 User’s Manual147.2 Explanation of Input/Output Signals (1) RXDSerial receiving data signal. On occurrence of framing error, overrun err

BD2-2880/2890 User’s Manual157.5 BufferingData transfer to the input buffer include DTR signals and TD signals as the control signalsconcerned.(1) DTR

iREVISIONRev. No. Date Content0.00 2000.06.26 Newly authored as a tentative edition for CS products reference.1.00 2002.08.09 Cover, Page 1, 2, 3, 7,

BD2-2880/2890 User’s Manual168. ERROR HANDLING8.1 Peripheral Circuit ErrorsThese errors are detected at power-on or initialization just after a reset.

BD2-2880/2890 User’s Manual17(3) Resetting methodsNote 1. When auto loading has not been selected with the function selection jumper (J4), set thepa

BD2-2880/2890 User’s Manual18Memory errorCutter lock (Cutter error)Head –upVP voltage errorHead temperature errorMacro execution waitErrorBlinking cyc

BD2-2880/2890 User’s Manual199. PRINTER MECHANISM CONTROL SYSTEM9.1 Thermal Head Control System (Division Driving System)The MLT-288 (Line thermal pri

BD2-2880/2890 User’s Manual209.2 Motor DriveThe MLT-288 uses a 4-phase bipolar stepping motor. It feeds the 1 dot line worth of paper intwo steps by

BD2-2880/2890 User’s Manual2110. MAINTENANCE AND SERVICEFor the information on maintenance and service, please contact our dealer or at the followinga

BD2-2880/2890 User’s Manual22 11. PRINT CONTROL FUNCTIONS 11.1 Command List Print Control Commands Print Charac

BD2-2880/2890 User’s Manual23 Bit Image Commands Status Command Panel Switch Command M

BD2-2880/2890 User’s Manual24ESC =ESC @DC2 A1Bh 3Dh n1Bh 40h12h 41h nControl CodeData input controlInitializing the PrinterSelecting the Print drive s

BD2-2880/2890 User’s Manual2511.2 Command Details11.2.1 Description of Items XXXX ALL Command Function A sequence of code constituting

iiCONTENTS1. OUTLINE ... 11.1 Fea

BD2-2880/2890 User’s Manual26LF Printing and Paper Feed Command <0A>H Prints data inside the input buffer and feeds lines based on the line f

BD2-2880/2890 User’s Manual27CR Print Command <0D>H 1) When DS 1-2 is OFF: This command is ignored. 2) When DS 1- 2 is ON: With data hel

BD2-2880/2890 User’s Manual28ESC J n Printing and feeding paper n/203 inch <1B>H<4A>H<n> {0 =< n =< FF} Data is described i

BD2-2880/2890 User’s Manual29ESC d n Printing and Feeding the paper by n lines <1B>H<64>H<n> * {0 =< n =< FF} Data is descr

BD2-2880/2890 User’s Manual30ESC SP n Setting the right space amount of the character <1B>H<20>H<n> {0 =< n=< 20} Data is

BD2-2880/2890 User’s Manual31ESC ! n Collective Specifying Printing Mode <1B>H<21>H<n> {0 =< n=< FF} Data is described

BD2-2880/2890 User’s Manual32LPRINT CHR$ (&H1B) + " ! " + CHR$ (&H00) + "H" ; LPRINT CHR$ (&H1B) + " ! " + C

BD2-2880/2890 User’s Manual33ESC % n Specifying/Canceling Download Character Set <1B>H<25>H<n> {0 =< n =< FF} data is des

BD2-2880/2890 User’s Manual34ESC & s n m [a Strany s a] m – n +1 Defining Download Character <1B>H<26>H<s><n><m> [

BD2-2880/2890 User’s Manual35[Example] Create each data bit by setting "1" for a printed dot and "0" for an unprinted d

iii8. ERROR HANDLING ... 168.1 Peripheral Circuit Erro

BD2-2880/2890 User’s Manual36ESC – n Specifying/ Canceling Underline <1B>H<2D>H<n> {0 =< n =< 02} data is described in Hex

BD2-2880/2890 User’s Manual37ESC E n Specifying/canceling highlighting <1B>H<45>H<n> {0 =< n =<FF} Data is described in He

BD2-2880/2890 User’s Manual38ESC G n Specifying/canceling Double Printing <1B>H<47>H<n> {0 =< n =< FF} Data is described

BD2-2880/2890 User’s Manual39ESC R n Selecting the International Character set <1B>H<52>H<n> {0 =< n =< 0A) Data is descr

BD2-2880/2890 User’s Manual40ESC V n Specifying/Canceling 90°-right- turned Characters <1B>H<56>H<n> {0 =< n =< 1} Data is

BD2-2880/2890 User’s Manual41ESC t n Selecting Character Code Table <1B>H<74>H<n> {0 =< n =< 1} Data is described in Hex co

BD2-2880/2890 User’s Manual42ESC { n Specifying/Canceling the Inverted Characters <1B>H<7B>H<n> {0 =< n =< FF} Data is d

BD2-2880/2890 User’s Manual43HT Horizontal Tab Command <09>H Shifts the printing position to the next horizontal tab position. • Ignored when

BD2-2880/2890 User’s Manual44ESC $ n1 n2 Specifying the Absolute Positions <1B>H<24>H<n1><n2> {0 =< n1 =< FF} {0 =&

BD2-2880/2890 User’s Manual45ESC D [ n ] k NUL Setting Horizontal Tab Position <1B>H<44>H [ <n> ] k<00>H {0 =< n =&l

BD2-2880/2890 User’s Manual11. OUTLINEThis control boards is designed to be used to control our thermal printer, “MLT-288/289” seriesthrough the compu

BD2-2880/2890 User’s Manual46ESC n1 n2 Specifying the Relative Positions <1B>H<5C>H<n1>< n2> {0 =< n1 =< FF} {0 =&l

BD2-2880/2890 User’s Manual47ESC a n Aligning the characters <1B>H<61>H<n> {0 =< n =< 2} Data is described in Hex code. A

BD2-2880/2890 User’s Manual48ESC 2 Specifying 1/6-inch line feed rate [Code] <1B>H<32>H The line feed rate per line is specified by

BD2-2880/2890 User’s Manual49ESC 3 n Setting line feed rate of minimum pitch <1B>H<33>H<n> {0 =< n =< FF} Data is described

BD2-2880/2890 User’s Manual50ESC * m n1 n2 [ d ] k Specifying the Bit Image Mode <1B>H<2A>H<m><n1><n2> [ <d>

BD2-2880/2890 User’s Manual51[Sample Program] LPRINT CHR$ (&H1B) + "*”; LPRINT CHR$ (0) + CHR$ (20) + CHR$ (0); IMG1 : GOSUB IMG1 LPRI

BD2-2880/2890 User’s Manual52GS * n1 n2 [ d ] n1 n2 8 Defining the Download Bit Image <1D>H<2A>H<n1><n2> [ < d &g

BD2-2880/2890 User’s Manual53 GOSUB IMG LPRINT CHR$ (&H1D) + "/" + CHR$ (0); LPRINT CHR$ (&H1D) + "/" + CHR$ (1); LPR

BD2-2880/2890 User’s Manual54GS / m Printing the Download, Bit Image <1D>H<2F>H<m> {0 =< m =< 03} Data is described in He

BD2-2880/2890 User’s Manual55ESC v (Serial Interface Only) Transmitting the printer status (Serial Type) <1B>H<76>H Current printer sta

BD2-2880/2890 User’s Manual22. BASIC SPECIFICATIONS2.1 Model ClassificationModels are identified by the following coding scheme:BD2 - 2880 U CCharac

BD2-2880/2890 User’s Manual56ESC c5 n Enabling/Disabling Panel Switches <1B>H<63>H<35>H<n> {0 =< n =< FF} Data is des

BD2-2880/2890 User’s Manual57GS : Starting / Ending Macro Definition <1D>H<3A>H Specifying starting / ending macro definition. Means te

BD2-2880/2890 User’s Manual58GS ^ n1 n2 n3 Executing the Macro <1D>H<5E>H<n1><n2><n3> {0 =< n1 =< FF} {0 =&l

BD2-2880/2890 User’s Manual59ESC i (When Using Auto Paper Cutter) Full Cut <1B>H<69>H Activating auto cutter unit (Full cut) • This

BD2-2880/2890 User’s Manual60ESC m (When Using Auto Paper Cutter) Partial Cut <1B>H<6D>H Activating auto cutter unit (Partial cut) •

BD2-2880/2890 User’s Manual61GS H n Selecting of Printing Position of HRI Code <1D>H<48>H<n> {0 =< n =< 3} Data is descri

BD2-2880/2890 User’s Manual62GS f n Selecting the font of HRI code <1D>H<66>H<n> n = 0, 1 Selecting the font of HRI code in printi

BD2-2880/2890 User’s Manual63GS h n Selecting the height of the Bar Code <1D>H<68>H<n> {1 =< n =< FF} Data is described in

BD2-2880/2890 User’s Manual64GS k n [ d ] k NUL Printing the Bar Code <1D>H<6B>H<n> [ < d> ] k <00>H {0 =< n =

BD2-2880/2890 User’s Manual65[Description of Bar Codes] <For print examples, see Page 67. > UPC-A This bar code, consisting of numerals only,

BD2-2880/2890 User’s Manual32.2 Basic SpecificationsPrinting systemPrint widthPrint SpeedNumber of columnsCharacter dimensionsCharacter typesBar code

BD2-2880/2890 User’s Manual66• Processing of the special characters The characters above the ASCII code number 96 are considered special characters

BD2-2880/2890 User’s Manual67[Description of Bar Codes] UPC-A, UPC-E, JAN-13 (EAN), JAN-8 (EAN), CODE39, ITF, CODABAR, CODE128 Type Print Sample Ou

BD2-2880/2890 User’s Manual68GS w n Selecting the horizontal size (Scale factor) of the Bar Code <1D>H <77>H<n> {2 =< n =<

BD2-2880/2890 User’s Manual69ESC = n Data Input Control <1B>H<3D>H<n> {0 =< n =< FF} Data is described in Hex code. Select

BD2-2880/2890 User’s Manual70ESC @ Initializing the Printer <1B>H<40>H Clears data stored in the print buffer and brings various setti

BD2-2880/2890 User’s Manual71DC2 A n Selecting the Print drive system <12>H<41>H<n> {0 =< n =< FF} Selecting the Fixed divis

BD2-2880/2890 User’s Manual7212. CHARACTER CODE TABLE12.1 International

BD2-2880/2890 User’s Manual7312.2 Japanese

BD2-2880/2890 User’s Manual7412.3 International Character SetCOUNTRY

BD2-2880/2890 User’s Manual75APPENDIX 1. BLOCK DIAGRAMCPUOSC 16.0MHFLASHMEMORYDriverRAMG/AResetCutterDriverDriverTimingOperation PanelSteppingMoterPap

BD2-2880/2890 User’s Manual43. CONNECTING CONNECTORS3.1 CN1 Connector for Printer Mechanism (For Print Head)3.2 CN2 Connector for Print Mechanism (For

BD2-2880/2890 User’s Manual76APPENDIX 2. Outer DimensionBD2–288IC2 IC1 CN1CN3CN475126741.63CN2TA2TA2IC101TA2TR2IC67280ø 2 × 4(Unit : mm)

BD2-2880/2890 User’s Manual53.3 CN3 Connector for Interface12345678910111213141516171819202122232425262728293031323334353637383940VccVccGNDGNDVpVpVpVp