Citizen C70 Specifikace Strana 12
- Strana / 385
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
I Alarms
Operation Errors (M)
I - 3
M01 External feed rate zero 0103
Details
MANUAL FEEDRATE switch on the machine operation panel is set to "0" when the machine
is in the JOG or automatic dry run mode.
"Manual feedrate B" is set to "0" during the JOG mode when manual feedrate B is valid.
"Each axis manual feedrate B" is set to "0" during the JOG mode when each axis manual fee-
drate B is valid.
Remedy
- Set the MANUAL FEEDRATE switch to a value other than "0" to release the error.
- If the MANUAL FEEDRATE switch has been set to a value other than "0" check for any short
circuit in the signal line.
- Correct the sequence program.
- Correct the external deceleration parameters as follows:
When "#1239 set11/bit6" is set to "0", set a non-zero value in "#1216 extdcc".
When "#1239 set11/bit6" is set to "1", set a non-zero value in "#2086 exdcax1" or "#2161
exdcax2" - "#2165 exdcax6" referring to the value set in the external deceleration speed se-
lection signal.
M01 F 1-digit feed rate zero 0104
Details
The F1-digit feedrate has been set to "0" when the F1-digit feed command was executed.
Remedy
- Set the F1-digit feedrate (from "#1185 spd_F1 (F1 digit feedrate F1)" to "#1189 spd_F5 (F1
digit feedrate F5)").
M01 Spindle stop 0105
Details
The spindle stopped during the synchronous feed/thread cutting command.
Remedy
- Rotate the spindle.
- If the workpiece is not being cut, start dry run.
- Check for any broken wire in the spindle encoder cable.
- Check the connections for the spindle encoder connectors.
- Check the spindle encoder pulse.
- Correct the program. (commands and addresses)
M01 Handle feed ax No. illegal 0106
Details
The axis, designated at handle feed, is out of specifications.
No axis has been selected for handle feed.
Remedy
- Check for any broken wires in the handle feed axis selection signal line.
- Correct the sequence program.
- Check the number of axes in the specifications.
M01 Spindle rotation speed over 0107
Details
Spindle rotation speed exceeded the axis clamp speed during the thread cutting command.
Remedy
- Lower the commanded rotation speed.
M01 Fixed pnt mode feed ax illegal 0108
Details
The axis, designated in the manual arbitrary feed, is out of specifications.
The feedrate in manual arbitrary feed mode is illegal.
Remedy
- Check for any broken wires in the axis selection signal line or the feedrate line for the manual
arbitrary feed mode.
- Check the specifications for the manual arbitrary feed mode.
M01 Block start interlock 0109
Details
An interlock signal has been input to lock the block start.
Remedy
- Correct the sequence program.
M01 Cutting block start interlock 0110
Details
An interlock signal has been input to lock the cutting block start.
Remedy
- Correct the sequence program.
M01 Restart switch ON 0111
Details
Restart switch has been turned ON and manual mode has been selected before the restart
search is completed.
Remedy
- Search the block to restart.
- Turn the restart switch OFF.
M01 Program check mode 0112
Details
The automatic start button was pressed during program check or in program check mode.
Remedy
- Press the reset button to cancel the program check mode.
M01 Auto start in buffer correct 0113
Details
The automatic start button was pressed during buffer correction.
Remedy
- Press the automatic start button after the buffer correction is completed.
M01 In reset process 0115
Details
The automatic start button was pressed during resetting or tape rewinding.
Remedy
- When rewinding the tape, wait for the winding to end, or press the reset button to stop the
winding, and then press the automatic start button.
- During resetting, wait for the resetting to end, and then press the automatic start button.
- Trademarks 2
- Contents 4
- IMPORTANT 5
- I Alarms 8
- 1. Operation Errors (M) 10
- I Alarms 11
- 2. Stop Codes (T) 15
- 3. Servo/Spindle Alarms (S) 19
- 3.4 Parameter Errors (S51) 31
- 3.5 Servo Warnings (S52) 32
- 4. MCP Alarms (Y) 35
- 5.1 Safety Observation Alarms 41
- 6. System Alarms (Z) 47
- 11. Multi CPU Errors (A) 57
- 12. Network Errors (L) 74
- 13. Program Errors (P) 80
- II Parameters 92
- 1. Machining Parameters 94
- Machining Parameters 96
- II Parameters 100
- 4. Servo Parameters 151
- 5. Spindle Parameters 177
- Spindle Parameters 193
- 6. Multi-CPU Parameters 217
- 7. FL-net Parameters 218
- 8. DeviceNet Parameters 227
- 10. PLC Parameters 238
- 11. Macro List 239
- 12. Position Switches 247
- III PLC Devices 264
- 1.1 System State 266
- 1.2 Axis State 272
- 1.3 Part System State 276
- 1.4 Spindle State 284
- 2.1 System State 287
- 2.2 Part System State 290
- 2.3 Axis State 295
- 2.4 Spindle State 296
- 3.1 System Command 298
- 3.2 Axis Command 304
- 3.3 Part System Command 310
- 3.4 Spindle Command 324
- 4.1 System Command 327
- 4.2 Part System Command 330
- 4.3 Axis Command 335
- 4.4 Spindle Command 337
- 5. Each Application 339
- 5.2 PLC Axis Control 342
- 5.3 Window Result Information 345
- 5.4 Window Command 350
- 5.7 Safety Observing 364
- 5.8 PLC Constants 367
- 5.9 PLC Bit Selection 370
- 6.1 Special Relay 374
- 6.2 Special Register 378
- Duplication Prohibited 384
Komentáře k této Příručce
Související produkty a manuály pro ne Citizen C70
ne Citizen C520 Uživatelský manuál
(6 stránky)
(6 stránky)
ne Citizen CBM-202 Series Uživatelský manuál
(28 stránky)
(28 stránky)
ne Citizen PHU Series s Uživatelský manuál
(36 stránky)
(36 stránky)
ne Citizen CUN60 Manuál s instrukcemi
(14 stránky)
(14 stránky)
ne Citizen 8203 Manuál s instrukcemi
(15 stránky)
(15 stránky)
ne Citizen D716 Uživatelský manuál
(102 stránky)
(102 stránky)
ne Citizen BR0123-09E Uživatelský manuál
(23 stránky)
(23 stránky)
ne Citizen PMU Series s Uživatelský manuál
(6 stránky)
(6 stránky)
ne Citizen Palidoro BW0172-53E Uživatelský manuál
(31 stránky)
ne Citizen EW9990-54E Uživatelský manuál
(1 stránky)
(1 stránky)
ne Citizen BV1060-15E Uživatelský manuál
(48 stránky)
(48 stránky)
ne Citizen 6765 Uživatelský manuál
(7 stránky)
(7 stránky)
ne Citizen AU1054-54G Uživatelský manuál
(14 stránky)
(14 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Hello Guys, Glad to Join! :)