Citizen C70 Specifikace stáhnout pdf (Strana 146)

II Parameters

Axis Specifications Parameters

II - 53

【#2062】 OT_1B+ Soft limit IB+

Set the coordinate of the upper limit of the area where the stored stroke limit IB is inhibited.

Set a value from zero point in the basic machine coordinate system.

---Setting range---

-99999.999 to 99999.999 (mm)

【#2063】 OT_1Btype Soft limit IB type

Select the type of stored stroke limit I in which "#2062 OT_1B+" or "#2061 OT_1B-" is

enabled.

0 : Enable Soft limit IB

1 : Disable Soft limit IB and IC

2 : Enable Soft limit IC

【#2068】 G0fwdg G00 feed forward gain

Set a feed forward gain for G00 pre-interpolation acceleration/deceleration.

The larger the setting value, the shorter the positioning time during in-position checking.

If a machine vibration occurs, set the smaller value.

---Setting range---

0 to 200 (%)

【#2069】 Rcoeff Axis arc radius error correction coefficient

Set the percentage to increase or decrease the arc radius error correction amount for each

axis.

---Setting range---

-100.0 to +100.0 (%)

【#2070(PR)】 div_RT Rotational axis division count

Set the number of divisions of one turn of the rotary axis under control.

(Example)

When "36" is set, one turn is supposed to be 36.000.

(Note 1) When "0" is set, the normal rotary axis (360.000 degrees for one turn) is assumed.

(Note 2) If this parameter is changed when the absolute position detection specification is

used, absolute position data will be lost. Initialization must be performed again.

---Setting range---

0 to 999

【#2073】 zrn_dog Origin dog Random assignment device

Set the input device in this parameter to assign the origin dog signal.

(Note 1) This parameter is valid when "1" is set in "#1226 aux10/bit5".

(Note 2) When this parameter is valid, do not set the existing device number. If the existing

device number is set, an emergency stop will occur. However, no device number

check will be performed for an axis to which the "near-point dog ignored" signal is

input.

---Setting range---

0000 to 02FF (HEX)

【#2074】 H/W_OT+ H/W OT+ Random assignment device

Set the input device in this parameter to assign the OT (+) signal.

(Note 1) This parameter is valid when "1" is set in "#1226 aux10/bit5".

(Note 2) When this parameter is valid, do not set the existing device number. If the existing

device number is set, an emergency stop will occur. However, no device number

check will be performed for an axis to which the "OT ignored" signal is input.

---Setting range---

0000 to 02FF (HEX)

【#2075】 H/W_OT- H/W OT- Random assignment device

Set the input device in this parameter to assign the OT (-) signal.

(Note 1) This parameter is valid when "1" is set in "#1226 aux10/bit5".

(Note 2) When this parameter is valid, do not set the existing device number. If the existing

device number is set, an emergency stop will occur. However, no device number

check will be performed for an axis to which the "OT ignored" signal is input.

---Setting range---

0000 to 02FF (HEX)

【#2076】 index_x

Not used. Set to "0".

【#2077】 G0inps G0 in-position width

Set the in-position width for G0.

Between SV024 and this parameter, the parameter with a larger value will be applied.

When "0" is set, this parameter will be invalid: only SV024 will be available.

---Setting range---

0.000 to 99.999 (mm)

1 2 ... 141 142 143 144 145 146 147 148 149 150 151 ... 384 385

Komentáře k této Příručce

Darricknus 16 Feb 2024 | 10:14:18

Hello Guys, Glad to Join! :)

Citizen C70 Specifikace Strana 146

Komentáře k této Příručce

Související produkty a manuály pro ne Citizen C70